Så er den gal, nyt system = ingen OC
Overclocking d. 06. december. 2004, skrevet af Gaffy
Vist: 417 gange.
Gaffy
#0
Efter at have læst om talrige overclockings eventyr bestilte jeg følgende:
MSI K8N neo2 plat g-54
AMD64 3000+ (0,9) kølet af en XP-90
Corsair 3200XLpro 2x512 matched pair (sidder som dual-channel i dimm 1+2)
Men mit system får gevaldige problemer når jeg prøver at pille ved FSB'en.
HTT er sat til x4
Rammene har jeg låst til 200
AGP er sat til 67
V-core har jeg prøvet alt fra 1.5 - 1.7 men lige meget hjælper det...
Af andre mærkelige ting har jeg disabled SATA 1-4, slået fastwrite fra..
Jeg ved ikke om min strømforsyning er det svage punkt, den er kun på 360watt, men den burde da kunne trække en smule..
MSI K8N neo2 plat g-54
AMD64 3000+ (0,9) kølet af en XP-90
Corsair 3200XLpro 2x512 matched pair (sidder som dual-channel i dimm 1+2)
Men mit system får gevaldige problemer når jeg prøver at pille ved FSB'en.
HTT er sat til x4
Rammene har jeg låst til 200
AGP er sat til 67
V-core har jeg prøvet alt fra 1.5 - 1.7 men lige meget hjælper det...
Af andre mærkelige ting har jeg disabled SATA 1-4, slået fastwrite fra..
Jeg ved ikke om min strømforsyning er det svage punkt, den er kun på 360watt, men den burde da kunne trække en smule..
#1
Start med at løsne timings og neddrosle rammene, sæt multiplyer til 4 og kør på FSB, så du kan se om det er mobo der giver probs. Prøv også at køre med LTD 3*FSB og slå endelig fastwrite til. Min vil ikke boote med disablet fastwrite...
360W burde ikke være et problem før du kommer mindst op på 250FSB med mindre du har 4316246 harddiske...
360W burde ikke være et problem før du kommer mindst op på 250FSB med mindre du har 4316246 harddiske...
#2
Nu har jeg ikke et A64, men er du sikker på at rammerne virkelige er låst? på xtremesystems har der været nogle problemer vedr. det :)
#3
Stjålet fra xtremesystems :) :
TIPS
TIP: you have to disable cool n quiet when ocing
TIP: Cpu fan header must be connected, if not the pc could experience boot problems
TIP: if you have problems booting with BH5 try another stick of memory and set vdimm to the max and make sure you set the cas latency to 2.5 or 2.0 as bh5 wont boot with cas 3.0, then swap in the BH5
TIP: the CPU backplate is hard to get off on the MSI ... just heat it with a hair dryer, it will come off easily then
TIP: for best performance the MSI only needs Vdimm/3.3V bypass mod (or the OCZ booster).
Yet to try a chipset mod or HTT mod on the MSI ... it may help with LDT 4x @ > 260 HTT bus speeds
TIP: shut down core center after you used it to adjust or check your settings, if left running it might crash your system
TIP: if you have problems booting at low temps with a winchester try the latest beta bios
TIP: disable fast writes
TIP: turn off NV/ATI Speed Up in the hidden bios settings
TIP: disable aggressive chipset timings (performance mode) when ocing
TIP: only bios 1.36beta and 1.37beta allow up to 1.9v vcore
TIP: color coded ram slots are different than other 939 boards. Slots 1&2 are the ones nearer to the CPU and are dual channel
TIP: use HTT multiplier 4x up to ~260 and 3x up to ~290
TIP: use the + and - or PgUP and PgDn keys to change the htt speed, DO NOT HIT ENTER
TIP: check out the official msi 939 neo2 tips and tricks guide thread
TIP: check out this 2 ram compability lists: 1 2
TIP: In the bios press and hold Shift+F2 and then press ALT+F3 to unlock "hidden" features within the BIOS
TIP: If anyone has trouble getting low temp readings downlaod the latest MBM5 (use the K8N NEO Plat mobo selection, click settings,temps,CPU,and choose the first option for Winbond Diode 2)
TIP: if you experience problems with Antec Neopower and Truepower PSUs and also with PowerStream PSUs, try Bios 1.37 and turn the PSU off after you shut down, seems to help as well
TIP: Dissable Agressive Timings in Cell Menu if you're going to overclock
TIP: some people had close to no thermal compount on the nb, if your nb runs hot add some thermal compound (WARNING! might hurt your warranty)
here is a guide that explains how to remove the nb heatsink
TIP: The MAch II needs a new firmware to operate with this board get it here
TIP: the vcore of winchesters seems to undervolt about 0.1V, max vcore for winchesters is 1.7V
TIP: bios collection: 1.10, 1.20, 1.23, 1.25, 1.30, 1.33, 1.34, 1.35, 1.36, 1.37, 1.41
TIP: beta biosses
TIP: 1.37 modded bios by Trats 1 2
TIP: lots of biosses, incl. beta and modded ones with changelogs
TIP: bios flash guide
TIP: windows tool bios flash guide
TIP: newer boards, with S/N:K0411xxxxxx and S/N:K0410xxxxxx, seem to no longer have a bug with winchesters at low minus temps
TIP: get Codered's A64 tweaker
TIP: if you have BH-5 memory use the A64 tweaker and lower the timings as described here
TIP: OC Guide for the msi k8n neo2 by XS GraveDiggA
right click save as and open with wordpad
TIP: corsair xl pro memory wont fit in the board with an xp-90 or xp-120 heatsink
TIP: the newer northbridges (0410/0411) seem to need less vdimm to reach the same overclock in 1:1!
TIP: If you are having trouble getting windows to boot from SATA ("Error Loading Operating System"), be sure to set SATA1/2/3/4 RAID to "ENABLED", even if you are not running RAID
TIP: older bios revisions need the agp speed set to 67mhz to lock it
TIP: if you boot with trcd 2 vdimm seems to drop 0.1v, boot with trcd 3 and use corecell or codered's a64 tweaker to set it to 2 in windows
TIPS
TIP: you have to disable cool n quiet when ocing
TIP: Cpu fan header must be connected, if not the pc could experience boot problems
TIP: if you have problems booting with BH5 try another stick of memory and set vdimm to the max and make sure you set the cas latency to 2.5 or 2.0 as bh5 wont boot with cas 3.0, then swap in the BH5
TIP: the CPU backplate is hard to get off on the MSI ... just heat it with a hair dryer, it will come off easily then
TIP: for best performance the MSI only needs Vdimm/3.3V bypass mod (or the OCZ booster).
Yet to try a chipset mod or HTT mod on the MSI ... it may help with LDT 4x @ > 260 HTT bus speeds
TIP: shut down core center after you used it to adjust or check your settings, if left running it might crash your system
TIP: if you have problems booting at low temps with a winchester try the latest beta bios
TIP: disable fast writes
TIP: turn off NV/ATI Speed Up in the hidden bios settings
TIP: disable aggressive chipset timings (performance mode) when ocing
TIP: only bios 1.36beta and 1.37beta allow up to 1.9v vcore
TIP: color coded ram slots are different than other 939 boards. Slots 1&2 are the ones nearer to the CPU and are dual channel
TIP: use HTT multiplier 4x up to ~260 and 3x up to ~290
TIP: use the + and - or PgUP and PgDn keys to change the htt speed, DO NOT HIT ENTER
TIP: check out the official msi 939 neo2 tips and tricks guide thread
TIP: check out this 2 ram compability lists: 1 2
TIP: In the bios press and hold Shift+F2 and then press ALT+F3 to unlock "hidden" features within the BIOS
TIP: If anyone has trouble getting low temp readings downlaod the latest MBM5 (use the K8N NEO Plat mobo selection, click settings,temps,CPU,and choose the first option for Winbond Diode 2)
TIP: if you experience problems with Antec Neopower and Truepower PSUs and also with PowerStream PSUs, try Bios 1.37 and turn the PSU off after you shut down, seems to help as well
TIP: Dissable Agressive Timings in Cell Menu if you're going to overclock
TIP: some people had close to no thermal compount on the nb, if your nb runs hot add some thermal compound (WARNING! might hurt your warranty)
here is a guide that explains how to remove the nb heatsink
TIP: The MAch II needs a new firmware to operate with this board get it here
TIP: the vcore of winchesters seems to undervolt about 0.1V, max vcore for winchesters is 1.7V
TIP: bios collection: 1.10, 1.20, 1.23, 1.25, 1.30, 1.33, 1.34, 1.35, 1.36, 1.37, 1.41
TIP: beta biosses
TIP: 1.37 modded bios by Trats 1 2
TIP: lots of biosses, incl. beta and modded ones with changelogs
TIP: bios flash guide
TIP: windows tool bios flash guide
TIP: newer boards, with S/N:K0411xxxxxx and S/N:K0410xxxxxx, seem to no longer have a bug with winchesters at low minus temps
TIP: get Codered's A64 tweaker
TIP: if you have BH-5 memory use the A64 tweaker and lower the timings as described here
TIP: OC Guide for the msi k8n neo2 by XS GraveDiggA
right click save as and open with wordpad
TIP: corsair xl pro memory wont fit in the board with an xp-90 or xp-120 heatsink
TIP: the newer northbridges (0410/0411) seem to need less vdimm to reach the same overclock in 1:1!
TIP: If you are having trouble getting windows to boot from SATA ("Error Loading Operating System"), be sure to set SATA1/2/3/4 RAID to "ENABLED", even if you are not running RAID
TIP: older bios revisions need the agp speed set to 67mhz to lock it
TIP: if you boot with trcd 2 vdimm seems to drop 0.1v, boot with trcd 3 and use corecell or codered's a64 tweaker to set it to 2 in windows
#5
LTD = HTT... i hvert fald i min bios ;)
altså HTT = 3*FSB så den kører et godt stykke under 1Ghz
altså HTT = 3*FSB så den kører et godt stykke under 1Ghz
#6
Og skriv evt hvad der går galt. Kan den ikke køre prime? Sort skærm? Skal du cleare CMOS før den vil boote igen? Låser den i windows?
#7
Og: TIP: If you are having trouble getting windows to boot from SATA ("Error Loading Operating System"), be sure to set SATA1/2/3/4 RAID to "ENABLED", even if you are not running RAID
Kunne måske være en mulighed...
Kunne måske være en mulighed...