4870X2 Fuld Vgpu/Vmemmod og køler guide
Grafikkort d. 01. december. 2008, skrevet af riska
Vist: 887 gange.
riska
#0
Here is a full modding guide for the Ati HD4870X2 gfx card.
you need a screwdriver and a sharp knife and a good solder iron and some small wires
And 2x50 Ohm and 1x50K Ohm Multiturn Vrs
And a lot of paticence.
The first thing we have to start with is to dismantle the card.
The card it self.
The back of the card.
And now to unscrew all the screws.
And then we can take the back cover of the card, be carefull not to harm the mempads
as you are gonna use them again.
Resten kan læses her
http://www.octeamdenmark.com/f...
I have done 5 cards this way now and it works great the cooler can be run at higher
fanspeed with the same noise and the card is about 20-25c lower at load temps.
And the cores can be run at 1.40-1.425v without a problem on stock cooler.
I have got my card up to 950 on both cores and the mem on 1090 stable and
1125 not stable but i have water on the card.
Note dont go any higher than 1.75-1.80v on the mems becaus they will articfact alot.
Happy modding from www.Octeamdenmark.com And me(riska)
you need a screwdriver and a sharp knife and a good solder iron and some small wires
And 2x50 Ohm and 1x50K Ohm Multiturn Vrs
And a lot of paticence.
The first thing we have to start with is to dismantle the card.
The card it self.
The back of the card.
And now to unscrew all the screws.
And then we can take the back cover of the card, be carefull not to harm the mempads
as you are gonna use them again.
Resten kan læses her
http://www.octeamdenmark.com/f...
I have done 5 cards this way now and it works great the cooler can be run at higher
fanspeed with the same noise and the card is about 20-25c lower at load temps.
And the cores can be run at 1.40-1.425v without a problem on stock cooler.
I have got my card up to 950 on both cores and the mem on 1090 stable and
1125 not stable but i have water on the card.
Note dont go any higher than 1.75-1.80v on the mems becaus they will articfact alot.
Happy modding from www.Octeamdenmark.com And me(riska)
#2
du gad ikke lige lægge flere billeder ind eller hvad?? :P
#3
der er da bare ekstremt mange billeder 😉
#4
Skal jeg udlede af det at du kører 950/1090 stabilt på stockkøleren eller hvordan? 🙂
#5
4# han har vist vand på det 🙂 I have got my card up to 950 on both cores and the mem on 1090 stable and
1125 not stable but i have water on the card.
iverfal sådan jeg fårstår det 🙂
1125 not stable but i have water on the card.
iverfal sådan jeg fårstår det 🙂
#6
det er fandme en fuldendt quide.. det skider jeg på. er du sindsyg den er veludført 😎 fandme iorden 😎 thumps up m8.. YOU ROCK 😴
#8
Takker mange gange der var faktisk omkring 45-55 billeder mere men de blev cuttet fra da det ellers vill tage alt for lang tid at lave tro mig det tager lang tid at copy paste alle de link så de ligger rigtigt