Ticonderoga
#0
Har haft gang i en større udskiftning hvor min gamle Q9650 + asrock mobo er blevet skiftet ud med en I7 970 + Asus rampage III extreme, så nu er turen kommet til at jeg vil prøve at OC den lidt. Tænkte omkring 3.8 - 4 ghz på stock vcore til at starte med.
Men bios'en på det asus mobo er vildt forvirrende, der er alllt for mange muligheder i forhold til mit gamle asrock (hvilket jo egentligt er en god ting 🙂 )
Så tænkte om nogen kendte til en god "bios skabelon" som jeg bare kan kopiere?
Men bios'en på det asus mobo er vildt forvirrende, der er alllt for mange muligheder i forhold til mit gamle asrock (hvilket jo egentligt er en god ting 🙂 )
Så tænkte om nogen kendte til en god "bios skabelon" som jeg bare kan kopiere?
#1
nice nok. men kender ikke biosen på asus. jeg kunne ikke oc det store på stock vcore men kunne kører 4.0ghz på ca1.35v
#2
Her er en rå template med mine I7 970 settings.
Target CPU Frequency 4500 MHz
Target DRAM Frequency XXXXMHz
LN2 Mode [Disabled]***
QPI Loadline Calibration [Enabled]***
Sync Mode []
AI Overclock Tuner []
OC From CPU level Up []
CPU Ratio Setting [25]
CPU Turbo Power Limit []
>CPU Configuration----------------------------
CPU Ratio Setting [25]
C1E Support [Disabled]
Hardware Prefetcher []
Adjacent Cache Line Prefetcher []
Intel(R) Virtualiyation Tech []
CPU TM Function [Disabled]
Execute Disable Bit []
Intel(R) HT Technology []
Active Processor Cores []
A20M []
Intel(R) SpeedStep(TM) Tech [Disabled]
Intel(R) C-STATE Tech []
C State package limit setting []
----------------------------------------------
BCLK Frequency [180]
PCIE Frequency [105]
DRAM Frequency []
UCLK Frequency []
QPI Link Data Rate []
Memory Configuration Protect []
>DRAM Timing Control--------------------------
CAS# Latency []
RAS# to CAS# Delay []
RAS# PRE Time []
RAS# ACT Time []
RAS# to RAS# Delay []
REF Cycle Time []
WRITE Recovery Time []
READ to PRE Time []
FOUR ACT WIN Time []
Back-To-BackCAS# Delay []
Timing Mode []
Round Trip Latency on CHA []
Round Trip Latency on CHB []
Round Trip Latency on CHC []
WRITE To READ Delay(DD) []
WRITE To READ Delay(DR) []
WRITE To READ Delay(SR) []
READ To WRITE Delay(DD) []
READ To WRITE Delay(DR) []
READ To WRITE Delay(SR) []
READ To READ Delay(DD) []
READ To READ Delay(DR) []
READ To READ Delay(SR) []
WRITE To WRITE Delay(DD) []
WRITE To WRITE Delay(DR) []
WRITE To WRITE Delay(SR) []
----------------------------------------------
CPU Differential Amplitude [800 MV]
CPU Clock Skew [100ps]
IOH Clock Skew [200ps]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [T-power]
PWR Volt. Control []
Load-Line Calibration [Enabled 100%]
CPU Voltege OCP []
CPU PWM Frequency [1000Hz]
Extreme OV []
Extreme OC []
CPU Voltage [1,40]
CPU PLL Voltage [1,81]
QPI/DRAM Core Voltage [1,38]
DRAM Bus Voltage [1,72]
>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA []
DRAM CTRL REF Voltage on CHA []
DRAM DATA REF Voltage on CHB []
DRAM CTRL REF Voltage on CHB []
DRAM DATA REF Voltage on CHC []
DRAM CTRL REF Voltage on CHC []
----------------------------------------------
IOH Voltage [1,17]
IOH PCIE Voltage [1,51]
ICH Voltage [1,15]
ICH PCIE Voltage [1,51]
---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
Svaret blev redigeret 2 gange, sidst af Rasmus66 d. 08-07-2011 18:06:27.
Target CPU Frequency 4500 MHz
Target DRAM Frequency XXXXMHz
LN2 Mode [Disabled]***
QPI Loadline Calibration [Enabled]***
Sync Mode []
AI Overclock Tuner []
OC From CPU level Up []
CPU Ratio Setting [25]
CPU Turbo Power Limit []
>CPU Configuration----------------------------
CPU Ratio Setting [25]
C1E Support [Disabled]
Hardware Prefetcher []
Adjacent Cache Line Prefetcher []
Intel(R) Virtualiyation Tech []
CPU TM Function [Disabled]
Execute Disable Bit []
Intel(R) HT Technology []
Active Processor Cores []
A20M []
Intel(R) SpeedStep(TM) Tech [Disabled]
Intel(R) C-STATE Tech []
C State package limit setting []
----------------------------------------------
BCLK Frequency [180]
PCIE Frequency [105]
DRAM Frequency []
UCLK Frequency []
QPI Link Data Rate []
Memory Configuration Protect []
>DRAM Timing Control--------------------------
CAS# Latency []
RAS# to CAS# Delay []
RAS# PRE Time []
RAS# ACT Time []
RAS# to RAS# Delay []
REF Cycle Time []
WRITE Recovery Time []
READ to PRE Time []
FOUR ACT WIN Time []
Back-To-BackCAS# Delay []
Timing Mode []
Round Trip Latency on CHA []
Round Trip Latency on CHB []
Round Trip Latency on CHC []
WRITE To READ Delay(DD) []
WRITE To READ Delay(DR) []
WRITE To READ Delay(SR) []
READ To WRITE Delay(DD) []
READ To WRITE Delay(DR) []
READ To WRITE Delay(SR) []
READ To READ Delay(DD) []
READ To READ Delay(DR) []
READ To READ Delay(SR) []
WRITE To WRITE Delay(DD) []
WRITE To WRITE Delay(DR) []
WRITE To WRITE Delay(SR) []
----------------------------------------------
CPU Differential Amplitude [800 MV]
CPU Clock Skew [100ps]
IOH Clock Skew [200ps]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [T-power]
PWR Volt. Control []
Load-Line Calibration [Enabled 100%]
CPU Voltege OCP []
CPU PWM Frequency [1000Hz]
Extreme OV []
Extreme OC []
CPU Voltage [1,40]
CPU PLL Voltage [1,81]
QPI/DRAM Core Voltage [1,38]
DRAM Bus Voltage [1,72]
>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA []
DRAM CTRL REF Voltage on CHA []
DRAM DATA REF Voltage on CHB []
DRAM CTRL REF Voltage on CHB []
DRAM DATA REF Voltage on CHC []
DRAM CTRL REF Voltage on CHC []
----------------------------------------------
IOH Voltage [1,17]
IOH PCIE Voltage [1,51]
ICH Voltage [1,15]
ICH PCIE Voltage [1,51]
---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
Svaret blev redigeret 2 gange, sidst af Rasmus66 d. 08-07-2011 18:06:27.
#3
Takker, vil jeg prøve at lege lidt med.
Er der iøvrigt nogen af jer som har prøvet at lege med det asus cpu level up? Øger det Vcore kraftigt?
Er der iøvrigt nogen af jer som har prøvet at lege med det asus cpu level up? Øger det Vcore kraftigt?
#4
#3 Har leget lidt med det og ja det øger vcore kraftigt, du kan selvfølgelig altid sætte den ned med TurboV.
#5
Er så småt gået igang.
Indtil videre er følgende ændret :
Vcore 1.25
FSB 174
Multiplier 23
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
LN2 Mode [Disabled]
QPI Loadline Calibration [Enabled]
Intel(R) SpeedStep(TM) Tech [Disabled]
Resten står på auto/default og jeg har ikke bootet ind i windows endnu. Er meget i tvivl og hele afsnittet med ram osv.
CPU PLL Voltage [1,25]
QPI/DRAM Core Voltage ????]
DRAM Bus Voltage [???]
Kører med 3 x 2 gb Kingston hyperX DDR3 2000mhz.
nogen som kan hjælpe mig lidt videre?
Indtil videre er følgende ændret :
Vcore 1.25
FSB 174
Multiplier 23
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
LN2 Mode [Disabled]
QPI Loadline Calibration [Enabled]
Intel(R) SpeedStep(TM) Tech [Disabled]
Resten står på auto/default og jeg har ikke bootet ind i windows endnu. Er meget i tvivl og hele afsnittet med ram osv.
CPU PLL Voltage [1,25]
QPI/DRAM Core Voltage ????]
DRAM Bus Voltage [???]
Kører med 3 x 2 gb Kingston hyperX DDR3 2000mhz.
nogen som kan hjælpe mig lidt videre?
#6
#5
Start med at sætte ram timmings lidt slappe så de ikke for systemet til at crashe når du kommer højt op i hastighed.
Prøv at sætte til dem 9-9-9-24-88 2T til at starte med
Cpu pll er meget forskellig fra cpu til cpu. Den funktion kommer først rigtig til sin ret når der kommer noget kulde på processoren. Nogle processorer skal køre med høj pll andre med lav.
Min 980X køre med 1,82 volt cpu pll da det er der den køre bedst andre skal ikke have mere ind 1,55 volt for at de køre godt på kulde.
Qpi/dram er IMC volten i forhold til rammene.
Prøv at start med at sætte den til 1,35 så kan du altid prøve at justere lidt på den for at se om det giver lidt mere hastighed på ram og cpu.
Dram voltage er ram volten.
Intel anbefaler at man ikke går over 1,65 volt, men det kan du sagtens køre. Har kørt med 1,82 volt på mine mushkin ram uden problemer.
Du skal bare huske at QPI/dram og VTT volten (hvis ens bios har den funktion) skal ligge inden for 0,5 volt af ram volten så kommer der ikke til at opstå nogle problemer.
Start med at sætte ram timmings lidt slappe så de ikke for systemet til at crashe når du kommer højt op i hastighed.
Prøv at sætte til dem 9-9-9-24-88 2T til at starte med
Cpu pll er meget forskellig fra cpu til cpu. Den funktion kommer først rigtig til sin ret når der kommer noget kulde på processoren. Nogle processorer skal køre med høj pll andre med lav.
Min 980X køre med 1,82 volt cpu pll da det er der den køre bedst andre skal ikke have mere ind 1,55 volt for at de køre godt på kulde.
Qpi/dram er IMC volten i forhold til rammene.
Prøv at start med at sætte den til 1,35 så kan du altid prøve at justere lidt på den for at se om det giver lidt mere hastighed på ram og cpu.
Dram voltage er ram volten.
Intel anbefaler at man ikke går over 1,65 volt, men det kan du sagtens køre. Har kørt med 1,82 volt på mine mushkin ram uden problemer.
Du skal bare huske at QPI/dram og VTT volten (hvis ens bios har den funktion) skal ligge inden for 0,5 volt af ram volten så kommer der ikke til at opstå nogle problemer.
#7
ok takker, prøver jeg lige at rode med igen.
Er der en måde hvorpå jeg kan kopiere min bios template så I kan følge med i den?
Er der en måde hvorpå jeg kan kopiere min bios template så I kan følge med i den?
#8
Hvordan ser dette ud ?
Target CPU Frequency 4000 MHz
Target DRAM Frequency ??MHz
LN2 Mode [Disabled]***
QPI Loadline Calibration [Enabled]***
Sync Mode []
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [23]
CPU Turbo Power Limit [Disabled]
>CPU Configuration----------------------------
CPU Ratio Setting [23]
C1E Support [Disabled]
Hardware Prefetcher [Disabled]
Adjacent Cache Line Prefetcher [Disabled]
Intel(R) Virtualiyation Tech [Disabled]
CPU TM Function [Disabled]
Execute Disable Bit [Disabled]
Intel(R) HT Technology [Enabled]
Active Processor Cores [1]
A20M [Disabled]
Intel(R) SpeedStep(TM) Tech [Disabled]
Intel(R) C-STATE Tech [??]
C State package limit setting [??]
----------------------------------------------
BCLK Frequency [174]
PCIE Frequency [100]
DRAM Frequency [?] Laveste??
UCLK Frequency [?] Laveste??
QPI Link Data Rate [?] Laveste?
Memory Configuration Protect [Enabled]
>DRAM Timing Control--------------------------
CAS# Latency []
RAS# to CAS# Delay []
RAS# PRE Time []
RAS# ACT Time []
RAS# to RAS# Delay []
REF Cycle Time []
WRITE Recovery Time []
READ to PRE Time []
FOUR ACT WIN Time []
Back-To-BackCAS# Delay []
Timing Mode []
Round Trip Latency on CHA []
Round Trip Latency on CHB []
Round Trip Latency on CHC []
WRITE To READ Delay(DD) []
WRITE To READ Delay(DR) []
WRITE To READ Delay(SR) []
READ To WRITE Delay(DD) []
READ To WRITE Delay(DR) []
READ To WRITE Delay(SR) []
READ To READ Delay(DD) []
READ To READ Delay(DR) []
READ To READ Delay(SR) []
WRITE To WRITE Delay(DD) []
WRITE To WRITE Delay(DR) []
WRITE To WRITE Delay(SR) []
----------------------------------------------
CPU Differential Amplitude [800 MV]
CPU Clock Skew [auto]
IOH Clock Skew [auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [T-power]
PWR Volt. Control [Auto]
Load-Line Calibration [Enabled 100%]
CPU Voltege OCP [Enabled]
CPU PWM Frequency [1000Hz]
Extreme OV [Enabled]
Extreme OC [Auto]
CPU Voltage [1,25]
CPU PLL Voltage [1,55] Er det nok?
QPI/DRAM Core Voltage [1,38]
DRAM Bus Voltage [1,6]
>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA []
DRAM CTRL REF Voltage on CHA []
DRAM DATA REF Voltage on CHB []
DRAM CTRL REF Voltage on CHB []
DRAM DATA REF Voltage on CHC []
DRAM CTRL REF Voltage on CHC []
----------------------------------------------
IOH Voltage [1,17]
IOH PCIE Voltage [1,51]
ICH Voltage [1,15]
ICH PCIE Voltage [1,51]
---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
Husk jeg går efter lidt ekstra ydelse med så lidt ekstra vcore og dermed varme som muligt da jeg kun kører på luft.
Target CPU Frequency 4000 MHz
Target DRAM Frequency ??MHz
LN2 Mode [Disabled]***
QPI Loadline Calibration [Enabled]***
Sync Mode []
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [23]
CPU Turbo Power Limit [Disabled]
>CPU Configuration----------------------------
CPU Ratio Setting [23]
C1E Support [Disabled]
Hardware Prefetcher [Disabled]
Adjacent Cache Line Prefetcher [Disabled]
Intel(R) Virtualiyation Tech [Disabled]
CPU TM Function [Disabled]
Execute Disable Bit [Disabled]
Intel(R) HT Technology [Enabled]
Active Processor Cores [1]
A20M [Disabled]
Intel(R) SpeedStep(TM) Tech [Disabled]
Intel(R) C-STATE Tech [??]
C State package limit setting [??]
----------------------------------------------
BCLK Frequency [174]
PCIE Frequency [100]
DRAM Frequency [?] Laveste??
UCLK Frequency [?] Laveste??
QPI Link Data Rate [?] Laveste?
Memory Configuration Protect [Enabled]
>DRAM Timing Control--------------------------
CAS# Latency []
RAS# to CAS# Delay []
RAS# PRE Time []
RAS# ACT Time []
RAS# to RAS# Delay []
REF Cycle Time []
WRITE Recovery Time []
READ to PRE Time []
FOUR ACT WIN Time []
Back-To-BackCAS# Delay []
Timing Mode []
Round Trip Latency on CHA []
Round Trip Latency on CHB []
Round Trip Latency on CHC []
WRITE To READ Delay(DD) []
WRITE To READ Delay(DR) []
WRITE To READ Delay(SR) []
READ To WRITE Delay(DD) []
READ To WRITE Delay(DR) []
READ To WRITE Delay(SR) []
READ To READ Delay(DD) []
READ To READ Delay(DR) []
READ To READ Delay(SR) []
WRITE To WRITE Delay(DD) []
WRITE To WRITE Delay(DR) []
WRITE To WRITE Delay(SR) []
----------------------------------------------
CPU Differential Amplitude [800 MV]
CPU Clock Skew [auto]
IOH Clock Skew [auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [T-power]
PWR Volt. Control [Auto]
Load-Line Calibration [Enabled 100%]
CPU Voltege OCP [Enabled]
CPU PWM Frequency [1000Hz]
Extreme OV [Enabled]
Extreme OC [Auto]
CPU Voltage [1,25]
CPU PLL Voltage [1,55] Er det nok?
QPI/DRAM Core Voltage [1,38]
DRAM Bus Voltage [1,6]
>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA []
DRAM CTRL REF Voltage on CHA []
DRAM DATA REF Voltage on CHB []
DRAM CTRL REF Voltage on CHB []
DRAM DATA REF Voltage on CHC []
DRAM CTRL REF Voltage on CHC []
----------------------------------------------
IOH Voltage [1,17]
IOH PCIE Voltage [1,51]
ICH Voltage [1,15]
ICH PCIE Voltage [1,51]
---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
Husk jeg går efter lidt ekstra ydelse med så lidt ekstra vcore og dermed varme som muligt da jeg kun kører på luft.
#9
Jeg køre nu med følgende settings :
================================================== ======
________________________________________________
Sync Mode..............................isable
A1 Overclock Tuner.....................:Manual
OC from CPU Level Up...................:Auto
CPU Ratio setting......................:x23
CPU Turbo Power Limit..................isable
<CPU Configuration Sub Menu>
CPU Ratio Setting...........................x23
C1E Support................................isable
Hardware Prefetcher..................:Enable
Adjacent Cache Line Prefetch.......:Enable
MPS and ACPI MADT Ordering.......:Mondern
Intel(r) Virtualization Tech............:Enabled
CPU TM Function............................isabled
Execute Disable Bit..........................:Enabled
Intel(r) HT Technology......................:Enabled.
Active Processor Cores.......................:All
A20M.............................................. ...isabled
Intel(r) Speedstep (TM) TEch.............isabled
Intel(r) Turbo Mode Tech....................isabled
Intel(r) C State Tech*............................isabled
________________________________________________
BCLK Frequency.........................:174
PCIE Frequency.........................:100
Dram Frequency.........................:1744
UCLK Frequency.........................:3488
QPI Link Data Rate.....................:auto
Memory Configuration Protect...........isable
--- > DRAM Timing Control
________________________________________________
CPU Differential amplitude.............:700mv
CPU Clock Skew.........................:normal
IOH Clock Skew.........................:normal
________________________________________________
Digi+ Power Mode.......................:T-balance
PWM Voltage Control....................:Auto
Load-Line Calibration..................:Full Calibration
CPU Voltage OCP........................:Enable
CPU PWM Frequency......................:Auto
________________________________________________
Extreme OV.............................isable
Extreme OC.............................:Auto
________________________________________________
CPU Voltage............................:1.33125
CPU PLL Voltage........................:1.70925
QPI/DRAM Core Voltage..................:1.3000
DRAM BUS Voltage.......................:1.60325
________________________________________________
IOH Voltage............................:1.1130
IOH PCIE Voltage.......................:1.51050
ICH Voltage............................:1.11300
ICH PCIE Voltage.......................:1.51050
________________________________________________
CPU Spread Spectrum....................isable
PCIE Spread Spectrum...................isable
________________________________________________
Men kernerne bliver alt for varme. I idle er de mellem 36 - 45 grader, men under load i link / prime95 bliver de midt 80'er inde jeg stopper testen. Er det min cpu voltage som er for høj og skaber for meget varme?
================================================== ======
________________________________________________
Sync Mode..............................isable
A1 Overclock Tuner.....................:Manual
OC from CPU Level Up...................:Auto
CPU Ratio setting......................:x23
CPU Turbo Power Limit..................isable
<CPU Configuration Sub Menu>
CPU Ratio Setting...........................x23
C1E Support................................isable
Hardware Prefetcher..................:Enable
Adjacent Cache Line Prefetch.......:Enable
MPS and ACPI MADT Ordering.......:Mondern
Intel(r) Virtualization Tech............:Enabled
CPU TM Function............................isabled
Execute Disable Bit..........................:Enabled
Intel(r) HT Technology......................:Enabled.
Active Processor Cores.......................:All
A20M.............................................. ...isabled
Intel(r) Speedstep (TM) TEch.............isabled
Intel(r) Turbo Mode Tech....................isabled
Intel(r) C State Tech*............................isabled
________________________________________________
BCLK Frequency.........................:174
PCIE Frequency.........................:100
Dram Frequency.........................:1744
UCLK Frequency.........................:3488
QPI Link Data Rate.....................:auto
Memory Configuration Protect...........isable
--- > DRAM Timing Control
________________________________________________
CPU Differential amplitude.............:700mv
CPU Clock Skew.........................:normal
IOH Clock Skew.........................:normal
________________________________________________
Digi+ Power Mode.......................:T-balance
PWM Voltage Control....................:Auto
Load-Line Calibration..................:Full Calibration
CPU Voltage OCP........................:Enable
CPU PWM Frequency......................:Auto
________________________________________________
Extreme OV.............................isable
Extreme OC.............................:Auto
________________________________________________
CPU Voltage............................:1.33125
CPU PLL Voltage........................:1.70925
QPI/DRAM Core Voltage..................:1.3000
DRAM BUS Voltage.......................:1.60325
________________________________________________
IOH Voltage............................:1.1130
IOH PCIE Voltage.......................:1.51050
ICH Voltage............................:1.11300
ICH PCIE Voltage.......................:1.51050
________________________________________________
CPU Spread Spectrum....................isable
PCIE Spread Spectrum...................isable
________________________________________________
Men kernerne bliver alt for varme. I idle er de mellem 36 - 45 grader, men under load i link / prime95 bliver de midt 80'er inde jeg stopper testen. Er det min cpu voltage som er for høj og skaber for meget varme?