Nyt Ryzen system ka' ikke genstarte!
Bundkort / CPU d. 11. maj. 2018, skrevet af Zahid
Vist: 1575 gange.
Zahid
#0
Alright guys. Har lige smidt et Asrock AB350 Pro4+Ryzen 1600x+Crucial 2666Mhz ram i mit kabinet og alt ser ud til at virke som det skal....PÅNÆR.....genstart! Den starter fint op fra et cold boot, men den går sort(hverken bios options eller windows splash) HVER gang jeg restarter fra windows. Jeg har googlet det så godt som jeg kunne men kunne ikke rigtigt finde en løsning. Jeg prøvede at køre uden XMP(2666) men det hjalp ikke. Jeg har prøvet en masse, men systemet vil simpelthen ikke genstarte fra windows men vælger i stedet at gå i sort inden der overhovedet dukker et bios boot logo op.
Nogen af jer gutter der har haft en lignende oplevelse og kan eventuelt komme med en løsning? Bundkortet er helt nyt og Ram-blokkene er slottet rigtigt, men alligevel.....
Tak på forhånd!
Tråden blev redigeret 2 gange, sidst af Zahid d. 11-05-2018 04:29:46.
Nogen af jer gutter der har haft en lignende oplevelse og kan eventuelt komme med en løsning? Bundkortet er helt nyt og Ram-blokkene er slottet rigtigt, men alligevel.....
Tak på forhånd!
Tråden blev redigeret 2 gange, sidst af Zahid d. 11-05-2018 04:29:46.
#1
Prøv det her:
SOLUTION TO PROBLEM:
Problem: UEFI settings not able to be accessed via Windows, no ASRock Boot Logo w/settings. Computer will just restart back to windows or show a black screen when booting to UEFI settings from Windows 10. This issue may apply to some AMD GPU's using Displayport and the UEFI Settings by default booting to your monitors native HD resolution. This must be disabled for you to be able to consistently boot back into UEFI Settings.
Solution:
Instructions(for dummies):
1. Power off computer completely and disconnect power, remove any externally powered analog speaker cables hooked into the jack.
2. Press the power button for 15 seconds to discharge the capacitors. Discharge any static or wear a static wrist band and pop the case open.
3. Under the second x8 PCI-E slot and at the bottom center of the Mobo, you will see a 3-Pin connector with a jumper on it. Remove the jumper and move it ONE PIN to the right.
4. Wait 5 seconds and move the jumper ONE PIN to the left.
5. Reconnect power and boot.
6. UEFI ASRock Splash Screen will show once and one time only so hit F2/DEL and boot to UEFI **WHEN THE LOGO APPEARS** HITTING F2/DEL BEFORE THE LOGO APPEARS WILL CAUSE THE SPLASH SCREEN NOT TO APPEAR AND YOU WILL HAVE TO RESTART AT STEP 1!!
7. Once in UEFI navigate to "Advanced" and use the down arrow until you highlight "Full HD UEFI"
8. A selection box will appear, select disable and hit enter.
9. Navigate to the "Exit" tab and select "Save Changes and Exit"
*Computer reboots and may display the post screen or just go to Windows*
SOLUTION TO PROBLEM:
Problem: UEFI settings not able to be accessed via Windows, no ASRock Boot Logo w/settings. Computer will just restart back to windows or show a black screen when booting to UEFI settings from Windows 10. This issue may apply to some AMD GPU's using Displayport and the UEFI Settings by default booting to your monitors native HD resolution. This must be disabled for you to be able to consistently boot back into UEFI Settings.
Solution:
Instructions(for dummies):
1. Power off computer completely and disconnect power, remove any externally powered analog speaker cables hooked into the jack.
2. Press the power button for 15 seconds to discharge the capacitors. Discharge any static or wear a static wrist band and pop the case open.
3. Under the second x8 PCI-E slot and at the bottom center of the Mobo, you will see a 3-Pin connector with a jumper on it. Remove the jumper and move it ONE PIN to the right.
4. Wait 5 seconds and move the jumper ONE PIN to the left.
5. Reconnect power and boot.
6. UEFI ASRock Splash Screen will show once and one time only so hit F2/DEL and boot to UEFI **WHEN THE LOGO APPEARS** HITTING F2/DEL BEFORE THE LOGO APPEARS WILL CAUSE THE SPLASH SCREEN NOT TO APPEAR AND YOU WILL HAVE TO RESTART AT STEP 1!!
7. Once in UEFI navigate to "Advanced" and use the down arrow until you highlight "Full HD UEFI"
8. A selection box will appear, select disable and hit enter.
9. Navigate to the "Exit" tab and select "Save Changes and Exit"
*Computer reboots and may display the post screen or just go to Windows*